PC Hardware in a Nutshell, 3rd Edition [Electronic resources] نسخه متنی

5.7 Installing Memory

Installing
a SIMM or DIMM module is straightforward. Most recent motherboards
automatically detect installed memory modules regardless of the slot
they occupy, but it is good practice to fill banks from the lowest
numbered to the highest. For example, if the motherboard has three
banks, fill Bank 1 only after Bank 0 is filled, and fill Bank 2 only
after Banks 0 and 1 are filled.

Some motherboards require larger modules be installed in
lower-numbered banks. For example, if the motherboard has three DIMM
sockets, Bank 0 is currently occupied by a 32 MB DIMM, and you are
installing two 64 MB DIMMs, instead of simply installing the two new
64 MB DIMMs in Banks 1 and 2, you may need to remove the 32 MB DIMM
from Bank 0, install the 64 MB DIMMs in Banks 0 and 1, and then
reinstall the original 32 MB DIMM in Bank 2.

That rule is not invariable, though. A few motherboards require
smaller modules be installed in the lower banks. Some motherboards
don't care which module you install in which bank.
Best practice is to check the manual before installing memory. If no
documentation is available, experiment by moving modules around. If
some or all of the memory is not recognized during the boot-time
memory check or in CMOS Setup, try rearranging the modules. If all
memory is recognized, you can safely assume that you have the modules
installed correctly.

Windows and recent Linux releases automatically recognize the full amount of memory physically installed. However, Linux kernel version 2.0.36 or earlier may not recognize more than 64 MB of RAM automatically. Some have reported this problem on older hardware even with newer kernels. If you upgrade RAM beyond 64 MB in such a system, add the line append="mem=XXXM" to the file /etc/lilo.conf, where XXX is the amount of physical RAM installed, and re-run /sbin/lilo to make the changes take effect. For example, if you install 256 MB, add append="mem=256M". One of our editors notes that you can also usually specify this at boot time, which can be useful for experimenting with different numbers (he came across one old system in which he needed to use one less than the total installed memory, or else Linux crashed). Also, lilo may be headed for extinction in favor of bootloaders such as grub, which reads its config file at boot time rather than requiring running a utility each time you change it. The best solution is to upgrade to a more recent Linux kernel.

5.7.1 Installing and Removing a SIMM

Locate
a free SIMM socket of the proper type (30- or 72-pin). One side of
the SIMM has a notch that aligns with a matching post on the SIMM
slot support bracket, which prevents the SIMM from being installed
backward. Align the notch and then slide the contact edge of the SIMM
into the SIMM slot at about a 45-degree angle, as shown in Figure 5-3.

Figure 5-3. Inserting the SIMM at a 45-degree angle

Once you have the SIMM aligned properly, maintain slight pressure
toward the slot and pivot the SIMM upward toward the vertical until
it snaps into place, as shown in Figure 5-4. Verify
that the spring connectors on each side of the SIMM slot bracket have
both snapped into the matching holes on the SIMM.

Figure 5-4. Rotating the SIMM to vertical and making sure the locking tabs snap into place

Locate
the spring connectors at the top of each side of the SIMM slot
bracket and press both of them lightly at the same time while
simultaneously pressing the SIMM gently away from the vertical. After
the spring connectors release their grip on the SIMM, pivot the SIMM
gently downward to about a 45-degree angle and then pull it gently
out of the slot. Locking tabs sometimes exert considerable force, so
you may find it easier to press the release gently with a small
screwdriver, as shown in Figure 5-5.

Figure 5-5. Using a small screwdriver to press down on the locking tabs until they release, while maintaining gentle pressure on the module

The motherboard shown in Figures 5-3 through Figure 5-5 uses metal locking tabs. Some inexpensive motherboards use plastic tabs, which are quite easy to break off. If a tab does break off, that SIMM slot is unusable because the pressure exerted by the tab is required to ensure good contact between the memory module and the slot contacts. Nearly all recent DIMM- and RIMM-based systems use plastic locking tabs, so the absence of metal tabs on these newer systems is not an indication of low quality.

5.7.2 Installing and Removing a DIMM or RIMM

Locate
a free socket and pivot the ejector arms on each side of the socket
as far as possible toward the horizontal. The contact edge of the
DIMM module is keyed with notches that correspond to protuberances in
the DIMM socket. Align the notches and slide the DIMM straight down
into the socket. Position your thumbs on top of the DIMM at each end
and press down firmly, as shown in Figure 5-6.

Figure 5-6. Aligning the memory module and pressing straight down until it seats

The DIMM slides (sometimes snaps) into the socket, which
automatically pivots the ejector arms toward the vertical. If the
ejector arms are not fully vertical, press them toward the DIMM until
they lock into the vertical position, as shown in Figure 5-7. Note that some DIMM sockets have minor
physical variations. If the DIMM does not fit easily into the socket,
do not force it. Contact the vendor who supplied the DIMM for a
replacement.

Figure 5-7. The ejector arms pivoting back to the vertical when the memory module is fully seated

If you are installing Rambus RIMMs, also install a CRIMM in each unused memory slot. Rambus systems malfunction unless all memory slots are occupied, either by a RIMM or a CRIMM. Most Rambus motherboards have enough CRIMMs bundled with the motherboard to populate all but one memory slot. If you run short of CRIMMs, you can buy them at most computer stores.

Pivot
both ejector arms simultaneously toward the horizontal position. The
DIMM simply pops out.

5.7.3 Testing and Configuring Newly Installed Memory

After
you install the new memory modules and verify that all is as it
should be, apply power to the system. The memory self-test should
increment up to the newly installed amount of memory. If it instead
shows only the original amount of memory, the cause is almost always
that you have not seated the new memory module completely. Power
down, reseat the module, and try again.

If the memory check shows an amount of memory larger than the
original amount but smaller than the expected new amount, the problem
is almost always that the BIOS and/or chipset do not support memory
modules of the size you've installed. If that
occurs, you may need to do one or more of the following things to
resolve the problem:

Check the Chipset Setup portion of CMOS Setup to determine how memory
is configured for the newly installed bank(s). Most recent chipsets
and BIOSs automatically determine the correct size and configuration
parameters for installed modules. But some chipsets, BIOSs, and
memory modules do not implement SPD correctly. If this occurs, you
may have to set the correct size manually, if indeed the module size
you have installed is an available option.

A limitation on maximum module size may be enforced by the chipset,
the BIOS, or both. Before deciding you cannot use the larger module,
check the motherboard manufacturer's web site for a
BIOS update. If the restriction on module size is enforced by the
BIOS but not by the chipset, you may find that a later BIOS revision
adds support for the larger module.

If all else fails, the only alternative may be to return the memory
module (you did make sure you had the right to return an incompatible
module, didn't you?) and obtain a smaller
module.